|
PID kits designed for Gaggia semi-auto
home
espresso machines.
What does a PID do & why should you have one on your Gaggia? Simply put
a PID is a super accurate and easily adjusted replacement for the Gaggia's OEM brew
and/or steam
thermostats. The OEM thermostats have a very wide dead-band of approximately
40 to 60 degrees Fahrenheit. This means that the actual temperature of the water in the boiler may be 20
to 30 degrees higher or lower than the optimum temperature for producing
quality espresso. With a PID the dead-band can be held to within a degree or two of the temperature you choose to brew at.
Another excellent reason to PID your Gaggia is that different single
origin coffees & espresso blends are best brewed at different temperatures
for optimal flavor extraction. The Gaggia's OEM brew thermostat cannot be
adjusted, so that even if it was accurate & had a narrower dead-band, the
coffee you spend so much money for may not taste best when brewed at the machine's
factory preset
& inflexible temperature setting. And yet another reason to PID your
Gaggia is to remedy the pitifully poor steaming performance of all Gaggia
machines. As shipped by the factory, and following the factory directions,
the Gaggia's might have enough steam power for one
cappuccino, but that's all. With my mods, the Gaggia has steam power to
equal machines selling for thousands of dollars more! These are the first PID kits designed specifically for the Gaggia
semi-auto line of home espresso machines. Each kit comes complete with all
parts needed plus clear & concise instructions for installing the kit.
These kits are intended for the average do-it-yourselfer, and require
only a few basic hand tools to install.
| Order Part # |
Typical Installation |
Description |
Price |
Parts Included |
Tools Required For Installation |
Comments |
| PCC-K001a |
 |
Gaggia kit, your choice of natural aluminum finish or
black anodized finish. Enclosure mounts on the left side of machine,
with all wiring routed internally. |
$185 *
**
(S&H included ) |
CAL3200 or CAL3300, 1/32 DIN temperature
controller (used, like new, or new old stock - no factory warranty),
Type 'T" washer mount thermocouple, 25-40 amp DC input SSR, in-line
fuse holder, enclosure, wiring & connectors. |
Drill, 7/16" drill bit, wire cutter/stripper/crimper,
Phillips screwdriver, #3 Allen wrench, various SAE wrenches. |
This kit is designed so all wiring is internal to the
enclosure & espresso machine. |
| PCC-K001b |
 |
Same as above, except I have added control of the
steam circuit into the PID's programming. |
$215 *
**
(S&H included ) |
Same as above, plus one additional power controller to accommodate the steam circuit programming. |
Same as above. |
This is a huge advantage over the OEM steam
thermostat, which has difficulty steaming enough milk for two lattes |
| PCC-T001a |
 |
Complete performance rebuild & fine-tuning of your
Gaggia espresso machine. |
$285 / $325
** (S&H included ) |
Machine modifications, as detailed in PCC-K001b;
to include brew & steam temperature management and on-the-boiler
thermocouple placement, will be installed, burned-in, & tested.
Disassembly & inspection of all parts; cleaning of boiler & all
valves, and reassembly using the finest RTV silicone sealants.
Temperature settings will be fine tuned and instructions will be
included to assist you in adjusting the temps to your tastes.
Group pressure will be set to ~9 bar. If your machine is
not equipped with an adjustable OPV/PRV, one will be added for $40
extra.
If defective parts are found (such as boiler, pump, etc.) which must be replaced
before work can proceed, I will
contact the owner with prices & obtain permission to replace them
before proceeding. |
None - You send me your espresso machine & I'll
return it to you with all of the mods made for you. |
This offers the non-DIY'rs the chance to enjoy shots
usually reserved for the gadget-heads. |
| PCC-M001a |
 |
I will drill and tap your boiler to accommodate a
compression fitting, into which I will mount a probe-style type "T"
thermocouple. |
$65 ** (S&H included )
*Sold only
in con- junction with either of the two PID kits indicated above.) |
Compression fitting & probe type "T" thermocouple. |
You send me the top half of your Gaggia boiler
when you order a PID kit & I will return to you the completed mod and your
PID kit. |
With this mod the PID is monitoring the water
temperatures inside the boiler. |
PID kits designed for Bunn ES-1A
commercial espresso machines.
What does a PID do and why should you have one on your Bunn? Simply put
a PID is a silent, super accurate, and easily adjusted replacement for the
Bunn's Sirai pressure stat. The sirai pstats have are very noisy. As
the mechanical relays open and close as the boiler temperature drops &
rises again and again, the three sets of relays are constantly clicking &
clacking.
Another excellent reason to PID your Bunn is that different single
origin coffees & espresso blends are best brewed at different temperatures
for optimal flavor extraction. The Bunn's pstat cannot be quickly and
accurately
adjusted, so the
coffee you spend so much money for may not taste best when brewed at a preset
& inflexible temperature setting. These are the first PID kits designed specifically for the
Bunn ES-1A line of commercial espresso machines. Each kit comes complete with all
parts needed plus clear & concise instructions for installing the kit.
These kits are intended for the average do-it-yourselfer, and require
only a few basic hand tools to install.
| PCC-K002a (for ES-1A or
any commercial HX machine) |
 |
Bunn ES-1A kit, your choice of natural aluminum finish or
black anodized finish. Enclosure mounts on the right side of machine,
with all wiring routed internally. |
$190 **
(S&H included ) |
CAL3200 or CAL3300, 1/32 DIN temperature
controller (used, like new, or new old stock - no factory warranty),
Type 'T" probe-style thermocouple or Omega washer-end type "T'
t/c, 25-40 amp DC input SSR, enclosure, wiring & connectors. |
Drill, 7/16" drill bit, wire cutter/stripper/crimper,
Phillips screwdriver, #3 Allen wrench, various SAE wrenches. |
This kit is designed so all wiring is internal to the
enclosure & espresso machine. |
How will Pearland Coffee Company
stand behind your purchase?
- A 7-day money back guarantee. If, after receiving the kit you decide
the project isn't for you, return it to us for a full refund of
purchase price (less shipping charges).
- A 90-day warranty from PCC on the kit parts. Return defective parts
to us and we will send you replacements, at no charge, within the
warranty period.
- PCC will be available via email & phone to answer any questions that
might arise.
-
How do I know that PCC's work is top-quality?
** Specifications are subject to change without
notification.
Email
Pearland Coffee Company
for more information or call 281.997.3504, M-F, 8-4 Central Time
Zone. |